Find local automotive repair shops in your area | AutoCodes.com Shops
Need A Repair Shop?
Find local automotive repair shops in your area.
CarZone Auto | Nissan and Infiniti Service Center
Do-It-Yourself Nissan Tutorials Home | Nissanhelp.com DIY DIY
 
Versa
 
Engine Control System
 
2007-2011 Nissan Versa Idle Air Volume Learning Procedure

2007-2011 Nissan Versa Idle Air Volume Learning Procedure

Models:
  • 2007 Nissan Versa
  • 2008 Nissan Versa
  • 2009 Nissan Versa
  • 2010 Nissan Versa
  • 2011 Nissan Versa

Idle Air Volume Learning is an operation to learn the idle air volume that keeps each engine within the specific range. It must be performed under any of the following conditions:

  • Each time electric throttle control actuator or ECM is replaced.
  • Idle speed or ignition timing is out of specification.

Instructions

Preparation

Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment.

  • Battery voltage: More than 12.9V (At idle)
  • Engine coolant temperature: 70 - 100 C (158 - 212 F)
  • Park/neutral position (PNP) switch: ON (Shifter in Park or Neutral)
  • Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
  • Steering wheel: Neutral (Straight-ahead position)
  • Vehicle speed: Stopped
  • Transmission: Warmed-up (Drive vehicle for 10 minutes.)

Procedure

  • 1
  • 2
  • 3
    Start engine and warm it up to normal operating temperature.
  • 4
    Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
  • 5
    Turn ignition switch OFF and wait at least 10 seconds.
  • 6
    Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
  • 7
    Repeat the following procedure quickly five times within 5 seconds.
  • a
    Fully depress the accelerator pedal.
  • 8
    Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON.
  • 9
    Fully release the accelerator pedal within 3 seconds after the MIL turned ON.
  • 10
    Start engine and let it idle.
  • 11
    Wait 20 seconds.
  • 12
    Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications.
  • Idle speed = 650 ± 50 rpm (in P or N position)
Nissan Versa DIY Projects
Modifications
Nissan Modification
Engine & Transmission
Nissan Engine and Transmission
Air Bag & Body Exterior/Interior
Nissan Air Bag, Body Exterior and Interior
OEM Accessories Installation Guides
Nissan Versa OEM Accessories Installation Guides
Electrical & Audio
Nissan Electrical and Audio
Heater & Air Condition
Nissan Heater and Air Condition
Suspension, ABS, Brakes & Tires
Nissan Brake and Suspension
Engine Control System
Nissan Engine Light
Nissanhelp.com Knowledgebase
Nissan Versa Service Bulletins Nissan Versa Campaigns/Recalls Nissan Versa Reference Specifications Tips & Articles
Nissan Versa Service Manuals Nissan Versa Owner's Manuals Nissan Versa Navigation System Manuals Nissan Versa Towing Guides
Nissan Versa Warranty Booklets Nissan Versa Detailing Tips and Articles Nissan Versa Maintenance Schedules Nissan Versa Forums
Nissan OBDII Code Chart Find a Shop Glossary of Automotive Terms Fuel Consumption Estimator